THH PLUS

SAJ

Zero grazer agricultural trailers Juscafresa.

Destined for mowing and forage transport.

Stands out for its system that starts with the movement of the plates that creates air turbulance that helps to move the feed into the bottom of the elevator. During the mower operation, the elevator put the forage on the front part of the trailer, and then the floor chains moves the material from the front to the back part of the trailer.

Standard equipped with:
Hydraulic installation system to use the elevator with refrigeration system
Fodder hydraulic back cover compass type
Cutting width 2100 mm
Hydraulically displaceable drawbar
ECI100: Square rocker axle 100 mm, 1900 track, 10 bolts, brakes 400x80

Capacity: 23 - 33m3

MODELS

S23THH

S28THH

S33THH

23,00m3

28,00m3

33,00m3

Dimensiones

	S23THH	S28THH	S33THH
M3	23	28	33
A	9240	10240	11240
B	5370	6370	7370
C	2550	2550	2550
D	1900	1900	1900
E	2680	2980	3680
F	1360	1360	1360
G	3080	3080	3080
H	550	550	550
I	1300	1300	1300
J	3020	3020	3020
K	2100	2100	2100
L	2000	2000	2000
O	4780	5780	6780

Descriptions, data and illustrations are only indicative. Juscafresa reserves the right to make any changes without prior notification.

Características

Mowing system

The process consists of cutting the fodder by the mower plates which at the same time makes an air turbulence that helps the entrance of the fodder to the bottom of the elevator.

The elevator has the function of raising the cut forage towards the front part of the trailer where the material will accumulate and will move towards the rear by the drag chains.

Plate mower

The top plate has three blades that create air turbulance that helps to move the feed into the bottom of the elevator.

The lower plates are entirely independent from the top plates and turning by the friction on the ground.

Mower

Mower with 1900mm of cutting width

Hydraulic independent system

Hydraulic independent system to use the elevator and dispenser.

The mower has one or two springs providing suspension so it can adapt to the terrain, and therefore avoid excessive friction of the plates on the ground.

Elevator

The feeder is raised by 6 ou 8 teeth and guided by channels, passing between the blades until the ejection in the body of the trailer. The tines are forked so they can pass through the cutting blades.

Unloading

Fodder hydraulic back cover.

Drive shaft

Homokinetic joint front transmission and friction disk clutch.

Back standard transmission and homokinetic joint.

Hydraulic kit

Electro-valves with control button box by cable to operate all the functions.

Button control

Button control with cable connection for all functions.

Automatic synchronizing for the unloading and security synchronization to avoid compressions on the dispenser.

Optional weighing system with load cells.

Drag system

Equipped with 4 chains 80/12X manufactured with 20Mn4+S355JO.

Drawbar

Hydraulically displaceable drawbar.

Axle

Square rocker axle 100 mm, 1900 track, 10 bolts, brakes 400x80.

Optional wheels

	S23THH	S28THH	S33THH
M3	23	28	33
A	9240	10240	11240
B	5370	6370	7370
C	2550	2550	2550
D	1900	1900	1900
E	2680	2980	3680
F	1360	1360	1360
G	3080	3080	3080
H	550	550	550
I	1300	1300	1300
J	3020	3020	3020
K	2100	2100	2100
L	2000	2000	2000
O	4780	5780	6780

“A higher quality finish means more machine life”

The Juscafresa finishing process is:

-Polishing of the whole machine removing the impurities that persist in the metal.

-Pressurized washing with degreaser solution to obtain a better grip on the primer and prevent corrosion.

-Wash at high pressure with hot water to remove dirt from the metal and remains of adhered products.

-Application of a high quality primer layer.

-Application of two layers of Juscafresa paint specially designed with our corporate color.

Descriptions, data and illustrations are only indicative. Juscafresa reserves the right to make any changes without prior notification.

Galeria

SAJTHHPLUS

1/9

Vídeos