+52 (1) 669 133 2505 +52 (1) 669 159 0889 info@agroexpertjuscafresa.com
Zero grazer agricultural trailers Juscafresa.
Destined for mowing and forage transport.
Stands out for its system that starts with the movement of the plates that creates air turbulance that helps to move the feed into the bottom of the elevator. During the mower operation, the elevator put the forage on the front part of the trailer, and then the floor chains moves the material from the front to the back part of the trailer.
Standard equipped with:
Hydraulic installation system to use the elevator and the dispenser motors with refrigeration system
Bilateral unloading by rubber conveyor chains 2360x900 mm with hydraulic displacement to the back part and hydraulic motor for its working
Dispenser provides continuous distribution for the unloading by two hydraulic motors, with electrohydraulic pressure switch that controls the advance of the floor chains
Cutting width 2100 mm
Hydraulically displaceable drawbar
ECI100: Square rocker axle 100 mm, 1900 track, 10 bolts, brakes 400x80
Capacity: 23 - 33m3
MODELS
S23DLDH
S28DLDH
S33DLDH
23,00m3
28,00m3
33,00m3
S23DLDH | S28DLDH | S33DLDH | |
|---|---|---|---|
M3 | 23 | 28 | 33 |
A | 9360 | 10360 | 11360 |
B | 5490 | 6490 | 7490 |
C | 2550 | 2550 | 2550 |
D | 1900 | 1900 | 1900 |
E | 2780 | 3080 | 3880 |
F | 1360 | 1360 | 1360 |
G | 3550 | 3550 | 3550 |
H | 550 | 550 | 550 |
I | 1300 | 1300 | 1300 |
J | 3020 | 3020 | 3020 |
K | 2100 | 2100 | 2100 |
L | 2000 | 2000 | 2000 |
N | 860 | 860 | 860 |
O | 4780 | 5780 | 6780 |
Q | 3220 | 3220 | 3220 |
Descriptions, data and illustrations are only indicative. Juscafresa reserves the right to make any changes without prior notification.
Mowing system
The process consists of cutting the fodder by the mower plates which at the same time makes an air turbulence that helps the entrance of the fodder to the bottom of the elevator.
The elevator has the function of raising the cut forage towards the front part of the trailer where the material will accumulate and will move towards the rear by the drag chains.
Plate mower
The top plate has three blades that create air turbulance that helps to move the feed into the bottom of the elevator.
The lower plates are entirely independent from the top plates and turning by the friction on the ground.
Mower
Mower with 1900mm of cutting width
Hydraulic independent system
Hydraulic independent system to use the elevator and dispenser.
The mower has one or two springs providing suspension so it can adapt to the terrain, and therefore avoid excessive friction of the plates on the ground.
Elevator
The feeder is raised by 6 ou 8 teeth and guided by channels, passing between the blades until the ejection in the body of the trailer. The tines are forked so they can pass through the cutting blades.
Unloading
Bilateral unloading by rubber conveyor chains 2360x900 mm with hydraulic displacement to the back part and hydraulic motor for its working.
Hydraulic unloading by floor chains by a hydraulic reducer.
The discharge platform moves hydraulically by hydraulic cylinder, being able to choose how to download: back, left or right side.
Dispenser provides continuous distribution for the unloading by two hydraulic motors, with electrohydraulic pressure switch that controls the advance of the floor chains.
The dispenser work as fodder on the discharge platform obtaining a continous and uniform distribution. It incorporates a displacement system at the back, which is activated during the download process by easing the fodder pressure during the charge process, and avoid possible blockage at the time of starting the rotation of the distribution chains of the dispenser.
The dispenser incorporates chains with spikes that start scraping the fodder inside the trailer, elevating to the top of the rotation of the chains and falling back on the discharge platform or the ground.
Automatic synchronizing for the unloading and security synchronization to avoid compressions on the dispenser.
Drive shaft
Homokinetic joint front transmission and friction disk clutch.
Back standard transmission and homokinetic joint.
Hydraulic kit
Electro-valves with control button box by cable to operate all the functions.
Button control
Button control with cable connection for all functions.
Automatic synchronizing for the unloading and security synchronization to avoid compressions on the dispenser.
Optional weighing system with load cells.
Drag system
Equipped with 4 chains 80/12X manufactured with 20Mn4+S355JO.
Drawbar
Hydraulically displaceable drawbar.
Axle
Square rocker axle 100 mm, 1900 track, 10 bolts, brakes 400x80.
Optional wheels
S23DLDH | S28DLDH | S33DLDH | |
|---|---|---|---|
560/45 R 22,5 | O | O | O |
“A higher quality finish means more machine life”
The Juscafresa finishing process is:
-Polishing of the whole machine removing the impurities that persist in the metal.
-Pressurized washing with degreaser solution to obtain a better grip on the primer and prevent corrosion.
-Wash at high pressure with hot water to remove dirt from the metal and remains of adhered products.
-Application of a high quality primer layer.
-Application of two layers of Juscafresa paint specially designed with our corporate color.
Descriptions, data and illustrations are only indicative. Juscafresa reserves the right to make any changes without prior notification.
